Tuesday 27 December 2011

Casteline Hair Sculpting Tutorial by Andy Bergholtz

All words and pictures Andy Bergholtz.



First, I warm up the Castilene in a microwave and work it in my hands like clay, applying the warm Castilene to the sculpture (Fig. 1) 


After I achieve the basic form using just my fingers, I'll then heat my sculpting tool and smooth the surface (Fig. 2, Fig. 3) 






I will continue to heat the tool during this process every few seconds, holding the tool very briefly over the flame. I will continue to refine the surface with this tool until I get a basic flow of detail that I like (Fig. 4, Fig. 5) 



Next, I will gently heat a small loop tool over a flame (Fig. 6), and will use this to carve some deeper detail into the form (Fig. 7). I will do this briefly, just to add a bit more depth to the form (Fig. 8)  






Next, I will very briefly heat a sanding pad over the flame (Fig. 9), and use this to smooth the surface a bit (Fig. 10). 



For this stage, you must heat the pad over the flame for only a half-second or so each time, VERY quickly or else it will begin to burn. You'll need to do this every 3-4 seconds while you work, and lightly drag the heated pad on the surface of the Castilene to smooth it. It sounds tricky, but it's quite simple. I'll do this until the hair is generally smoothed and ready to begin detailing (Fig. 11). 



For detailing, I heat my metal tool over the flame once again (very very quickly this time, only to warm it up a little... you don't want it to be too hot, only warm enough so it doesn't "stick" to the Castilene). Then I will use the edge of the tool to "press and roll" detail into the surface of the Castilene (Fig. 12) 




This "press and roll" method is the most important step in my detailing technique. I will continue doing this until I've achieved the level of detail that I want (I try to avoid dragging or 'scribing' detail in this stage, as that is what often causes the unwanted "crumb effect"). For smaller curves, I will use a smaller tool and even a round loop tool sometimes, but the "press and roll" method still applies (Fig. 13, 14, 15) 








Finally, sometimes I will lightly brush down the surface with lighter fluid (Fig. 16). I do this VERY little, as using too much will make the surface grainy and mushy, so use it sparingly (Fig. 17) 



Just make sure to only brush lighter fluid on Castilene when you are completely finished with the sculpting, as it's very difficult to re-sculpt any area that has already been brushed. The hair is finished! (Fig. 18) 




18 comments:

  1. Really amazing. I've been lookin for something like that for years. Thank you very much for it, thanks!

    ReplyDelete
  2. Omg I did not know you had a Blog Finally I found you. Love your work and a HUGE Thanks for sharing your knowledge and skill!

    ReplyDelete
  3. your product image excellent and work awesome of solder wire. i am become your fan http://www.ansolsolder.co/

    ReplyDelete
  4. Very inspiring piece. Thank you for sharing this wonderful sculpture.

    ReplyDelete
  5. Great Tutorial. Very valuable for beginners. THX for sharing :-)

    ReplyDelete
  6. Hello, i like your work mr

    Visit our store and sell your costum action figure
    jactionfigure.com

    We love action figure

    Thanks admin

    ReplyDelete
  7. Wow that is great thank yo for sharing

    ReplyDelete
  8. Nice information posted here.we are one of the best steel wire provider in the market.Whoever want to buy steel wire,visit Precision Drawell or call +917620078063.

    ReplyDelete
  9. Great tips and great technique. thanks

    ReplyDelete
  10. We are one of the leading manufacturers and supplier of Display Counters, Display Counters manufacturer in Delhi, which are available for restaurants and commercial food joints to change the look.any ishu call me +91-9899744933

    Display Counter manufacturers in Gurgaon

    ReplyDelete
  11. RMS SIGN offers a wide range of backlit/ glow sign display light boxes giving you the best options for your illuminated display requirements. We have 8 years of great experience in glow sign board manufacturing and repairing. any ishu contact this numaber +91-9999142017
    Glow Sign Board manufacturers in Rajouri Garden

    ReplyDelete